Alloy AD35 is used: for the manufacture of semifinished products by hot or cold deformation; profile and pipe extrusion presses for the production of various sredneshirotnykh details.

Note

The alloy system Al-Mg-Si.
ISO 209−1 alloy brand AD35 has designations and AlSi1MgMn 6082.

Standards

Name	Code	Standards
Name	Code	Standards
Tubes of non-ferrous metals and alloys	В64	GOST 18482-79
Bars	В55	GOST 21488-97
Non-ferrous metals, including rare, and their alloys	В51	GOST 4784-97, OST 1 92014-90
Bars and shapes	В52	GOST 8617-81, GOST 13616-97, GOST 13617-97, GOST 13618-97, GOST 13619-97, GOST 13620-90, GOST 13621-90, GOST 13622-91, GOST 13623-90, GOST 13624-90, GOST 13737-90, GOST 13738-91, GOST 17575-90, GOST 17576-97, GOST 29296-92, GOST 29303-92, GOST Р 50066-92, GOST Р 50067-92, GOST Р 50077-92, OST 1 92093-83
Sheets and strips	В53	TU 1-1-8-79

Chemical composition

Standard	Mn	Cr	Si	Fe	Cu	Al	Ti	Zn	Mg
Standard	Mn	Cr	Si	Fe	Cu	Al	Ti	Zn	Mg
GOST 4784-97	0.4-1	≤0.25	0.7-1.3	≤0.5	≤0.1	Rest	≤0.1	≤0.2	0.6-1.2
OST 1 92014-90	0.5-0.9	-	0.8-1.2	≤0.5	≤0.1	Rest	≤0.15	≤0.2	0.8-1.4

Al is the base.
According to GOST 4784-97 the chemical composition is given for the alloy AD35. Mass fraction of each other impurity (not regulated) ≤ 0.05%, total mass fraction of other impurities ≤ 0.15%.
According to OST 1 92014-90 the chemical composition is given for the alloy AD35. Mass fraction of each other impurity (not regulated) ≤ 0.05%, total mass fraction of other impurities ≤ 0.10%.

Mechanical properties

Section, mm	s_T\|s_0,2, MPa	σ_U, MPa	d₅, %
Section, mm	s_T\|s_0,2, MPa	σ_U, MPa	d₅, %
Extruded normal strength according to GOST 8617-81 in the delivery condition (longitudinal samples)
	≥108	≥196	≥12
100	≥245	≥314	≥8
The pressed bars normal strength in the delivery condition according to GOST 21488-97 (longitudinal samples)
8-300	≥110	≥195	≥12
8-100	≥245	≥315	≥8
Tubes extruded in the state of delivery according to GOST 18482-79 (samples, in cross-section shows the thickness of the wall)
	≥100	≥200	≥14
2-40	≥200	≥270	≥10

Description mechanical marks

Name	Description
Name	Description
s_T\|s_0,2	Yield strength or limit of proportionality with a tolerance for residual deformation of 0.2%
σ_U	Limit short-term strength
d₅	Elongation after rupture

Physical characteristics

Temperature	r, kg/m³
Temperature	r, kg/m³
20	2700

A description of the physical symbols

Name	Description
Name	Description
Е	The normal elasticity modulus
r	Density
l	Coefficient of thermal conductivity
R	UD. the resistivity

Technological properties

Name	The value
Name	The value
Weldability	Good.
Pressure treatment	Mostly in hot condition.

Alloy AD35 (1350)

Designation

Description