Sheet, round, wire ХН60М - ЭП367
International Equivalent
Mark | Analogue | W. Nr. | Aisi Uns | En | Order |
---|---|---|---|---|---|
ХН60М | EP367 | Delivery from the stock, in stock | |||
06Х15Н60М15 | EP367 | Delivery from the stock, in stock |
Relevance
Heat-resistant iron-nickel alloy HN60M mark (06H15N60M1; EP367) is used in the manufacture of rotors, disks, flat springs, fasteners, produced by cold heading, turbine blades and other parts that operate at t ° to + 650 ° C… Manufacturing normalized GOST 5632−72 «High-alloy steels and high-temperature corrosion-resistant and heat-resistant alloys», as well as specifications 14−11−245−88 «steel shaped profiles of high precision».
Chemical composition
Cr | C | Al | Cu | Mo | Mn | Fe | Ni | Si | S | P | W | Ti |
---|---|---|---|---|---|---|---|---|---|---|---|---|
14,0−16,0 | ≤0,12 | - | ≤0,30 | - | 1.0−2.0 | The basis | 34,0−38,0 | ≤0,60 | ≤0,020 | ≤0,030 | 2.8−3.5 | 1.1−1.5 |
The physical characteristics of the alloy brand HN60M
U rev. | Test temperature, ° C | 900 | 800 | 700 | 600 | 500 | 400 | 300 | 200 | 100 | 20 | 0 |
---|---|---|---|---|---|---|---|---|---|---|---|---|
(G, GPa) | The modulus of elasticity in the torsional shear | |||||||||||
(E, GPa) | The module of elasticity | 150 | 158 | 166 | 173 | 179 | 186 | 190 | 195 | 202 | 198 | |
(R, kg / m3) | Density | 8160 | 8164 | |||||||||
(R, nom · m) | Electrical Resistivity | 1170 | 1160 | 1150 | 1120 | 1100 | 1050 | 1020 | ||||
(L, W / (m · ° C)) | Coefficient of thermal conductivity | 26 | 24 | 22 | 21 | 19 | 17 | 16 | 13 | |||
(C, J / (kg · ° C)) | Specific heat | |||||||||||
(A, 10−6 1 / ° C) | The coefficient of linear thermal expansion | 16.9 | 17.7 | 16.6 | 16.6 | 16.1 | 15.9 | 15.5 | 15.1 | 14.8 |
Legend:
Marking the physical properties:
Description | designation |
---|---|
— Temperature data acquisition of the alloy [Castle] | — T |
— Modulus of elasticity of the 1st kind, [MPa] | — E |
— Coefficient of linear thermal expansion (at 20 ° C) [1 / deg] | -a |
— The electrical resistance [ohm · m] | -R |
— Specific weight [g / cm3] | -r |
— Thermal conductivity [W / (m · deg)] | -l |
— Specific heat capacity (at 20 ° C) [J / (kg · deg)] | -C |
delivery condition | Cross-section, mm | sB, MPa | d5,% | d4 | tisp., ° C | totpusk, ° C | St | S0,2, MPa | d | d10 | y,% | HRB | HV | HSh | KCU, kJ / m2 | HB | HRC |
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
HN35VT-VD | ≤200 | ≥830 | ≥18 | ≥490 | ≥40 | ≥588 | 207−269 | |||||||||
HN35VT | ≤650 | ≥735 | ≥15 | ≥392 | ≥25 | ≥686 | 207−269 |
Marking the mechanical properties:
Description | designation |
---|---|
— The limit of proportionality (the yield strength for the residual strain) [MPa] | sT |
— Short-term strength [MPa] | sre |
— Reduction [%] | y |
— Elongation at break [%] | d5 |
— Brinell hardness in [MPa] | HB |
— Impact strength [kJ / m2] | KCU |
Welded assemblies and workpiece parts of pipe fittings in accordance with ST CKBA 016−2005. Aging at temp.850−900 ° C (delayed 10 hours) + hardening in water at temp.1080−1100 ° C (delayed 1.0−1.5 hours, 1.5−2.5 hours, — to the workpiece 90−150 mm), while the rate of aging. 690−710 ° C (with an exposure 10−50 h) + air cooling, air cooling (to be a single mark HN60M aging temp. 700 ° C (with an exposure of 50 hours), cooling the air). The shape, size, assortment became subject to the following requirements:
GOST 8560−78 — Hexagon calibrated;
GOST 4405−75 — hot-rolled and forged stripe;
GOST 103−76 — hot-rolled stripe;
GOST 2879−88 — Hexagon hot;
14−2-205−87 OST, GOST 2591−88 — hot rolled square;
Standard 1133−71- forged square and round;
GOST 7417−75 — calibrated round.
14 GOST 955−77 — with specials. surface finish;
Standard 2590−88- hot rolled round;
GOST 8559−75 — square calibrated;
Weldability:
designation | Description |
---|---|
limited weldability | — Needs to preheating t ° 100−120 ° C with a final heat treatment |
no limits | — No need for preliminary heating and final heat treatment |
difficult to weld | — Needs to preheating t ° 200−300 ° C with a final heat treatment |
Buy at the best price
HN60M assortment of brand products by LLC «Electrovek-steel» will satisfy any customer. Price is determined by the technological features of production without including additional costs. We easily purchase wholesale all the necessary products for large-scale productions. We also offer favorable conditions for retail customers. Technological equipment for each stage of our production enables us to fulfill individual orders of non-standard options. Evek.org on our website. you will find all the necessary information about the products can download the product catalog, see price list. We are waiting for your orders.