12Х18Н10Т-1.4878 pipe, wire, circle

Sheet, tape

International Equivalent

Mark Analogue W. Nr. Aisi Uns En Order
12X18H10T EP2 1.4541 321 X12CrNiTi18-10 Delivery from the stock, in stock
12Х18Н10Т-Н EP2 1.4541 321 X12CrNiTi18-10 Delivery from the stock, in stock
12X18H10T-M EP2 1.4541 321 X12CrNiTi18-10 Delivery from the stock, in stock
12Х18Н10Т-В EP2 1.4541 321 X12CrNiTi18-10 Delivery from the stock, in stock
12X18H10T-TS Delivery from the stock, in stock
12Х18Н10Т-ТС-1 Delivery from the stock, in stock

Relevance

Steel of austenitic class, heat and corrosion resistant. Alloyed with 17−19% Cr, 9−11% Ni, up to 2% Mn. Used in power engineering at t° ≤ 600 °C. E.g. for heat-exchange fittings of TVEL with water coolant, turbine blades, parts of compressors and pumps. Welded reactors of this alloy work in dilute solutions of acetic, nitric, phosphoric acids, saline and alkaline solutions. Parts operating under load can withstand temperatures from -196 ° C to +600 ° C, and in aggressive environments — up to +350 ° C. The substitutes are 08X22H6T, 08X17T, 08X18H8N2T, 10X14H14N4T, 12X17H9AN4, 15X25T, 12X18H9T.

Supplies

Sections of 12X18N10T grade, including shaped, are produced in accordance with the following State Standards: 5949−75; 2590−88; 2879−88; 2591−88. Thick plate — 7350−77. Thin plate — 5582−75. Tape — 4986−79. Strip — State Standards 4405−75 and 103−76. Forgings and forged blanks — 1133−71 and 25,054−81. Tubes — 9940−81 and 9941−81. Wire — 18,143−72. Ground bar and silverware — 14,955−77 and 18,907−73. Calibrated bar — 7417−75; 8559−75 and 8560−78.

Percent composition of 12X18N10T (GOST 5632−72)

С Si Mn Cr Ni Ti Р S Cu
0,12 0,8 2,0 17,0−19,0 9,0−11,0 5 С-0,8 0,02 0,035 0,30

Technological properties

Hot deformation occurs in the temperature range from 1200 °C to 850 °C. Semifinished products up to 350 mm thick are air-cooled. Weldability — without limitations. Welding methods: RDS (electrodes ЦТ-26), ЕШС and КТС. Final heat treatment is desirable. Can be processed by cutting — Kvtv. spl = 0.85 and Kvb.st. = 0.35 in the quenched state at HB 169 and σc = 610 MPa. According to corrosion properties it is close to steel 12Х18Н9Т.

Heat resistance

Medium Temperature°С Resistance group or grade
Air 650 2−3
  750 4−5

In heat resistance it is close to steel 12Х18Н9Т

Mechanical properties

GOST Range Thickness, mm σ0.2 MPa σ in MPa δ5,% ψ,%
5949−75 Bar hardened at t° up to 1020 °C with cooling by air, oil or water. 60 196 540 40 55
18 907−73 Grinding bars, machined to the specified strength ≤ 5 _ - 590−830 930 20 — _ -
7350−77 5582−75 Hot- and cold-rolled sheets; quenched at 1000−1080°C in water or in air Quenched at 1050−1080°C in water or in air More than 4 ≤ 3.9 216 205 — 530 530 880−1080 38 40 10 _ — -
25 054−81 Forging quenched at t° up to 1100 °C with air or water cooling. ≤ 1000 196 510 35 40
18 143−72 Wire: heat-treated 1−6 - 540−880 20 -
9940−81 Seamless hot-deformed pipe without heat treatment 3,5−32 - 529 40 -

Mechanical properties depend on t° of heating

tisp°С σ0.2 MPa σ in MPa ψ,% δ5,% KCU J/cm2
20 225−315 550−650 66−80 46−74 215−372
500 135−205 390−440 60−70 30−42 196−353
600 120−205 340−410 51−74 28−38 196−358
700 120−195 265−360 40−70 20−38 255−353

Note. Tempering from 1050−1100 °C in air.

σc — Ultimate short-term strength, [MPa].

δ5, — Tensile elongation at break, [ % ].

ψ — Tensile stress, [ % ].

Buy at the best price

Evek GmbH sells a wide range of stainless steel products. Our representative offices are located. You can make a purchase without leaving your office, through the Company’s website. The technological configuration of each production stage makes it possible to fulfill individual orders, if you are not satisfied with the basic products. We carry out high quality individual orders of non-standard parameters, the terms of their performance are minimal. In case of bulk purchases we provide discounts.