VT20-2 St. titanium welding wire
International Equivalent
Mark | Analogue | W. Nr. | Aisi Uns | En | Order |
---|---|---|---|---|---|
ВТ20-2 | Delivery from the stock, in stock |
Relevance
Titanium welding wire brand VT20−2sv, implemented by LLC «Electrovek-steel», meets the most stringent national and foreign standards. Popularity of the wire due to high quality, diversified product mix, the optimum value.
alloy Brand: | Classification: | Industrial use: |
---|---|---|
VT20−2sv | Titanium wrought alloys | production of welding wire |
The percentage of VT20−2sv alloy 27 according to GOST 265−87
Si | C | Fe | Mo | Ti | N | V | Al | H | O | Zr | Impurities |
---|---|---|---|---|---|---|---|---|---|---|---|
≤0.1 | ≤0.05 | ≤0.15 | 0.5 — 1.5 | 89.86 — 94.2 | ≤0.04 | 0.5 — 1.5 | 3.5 — 4.5 | ≤0.003 | ≤0.12 | 12 | other 0.3 |
Note: Titanium is a base; its percentage of about 89.86 — 94.2%.
Mechanical properties of titanium wire VT20−2sv (20 ° C).
assortment | The size | Eg. |
---|---|---|
Wire, 27 GOST 265−87 | 10 | 635−835 |
Physical characteristics VT20−2sv alloy.
W / (m · deg) | 1 / Grad | MPa | hail | kg / m3 | Ohm m | J / (kg · °) |
---|---|---|---|---|---|---|
l | a June 10 | 100 | 540 | |||
8.2 | 1.12 | 20 | 4505 | |||
18.85 | E 10- 5 | T | r | R September 10 | C |
Marking the physical properties:
Description | designation |
---|---|
— Temperature data acquisition of the alloy [Castle] | — T |
— Modulus of elasticity of the 1st kind, [MPa] | — E |
— Coefficient of linear thermal expansion (at 20 ° C) [1 / deg] | -a |
— The electrical resistance [ohm · m] | -R |
— Specific weight [g / cm3] | -r |
— Thermal conductivity [W / (m · deg)] | -l |
— Specific heat capacity (at 20 ° C) [J / (kg · deg)] | -C |
Marking the mechanical properties:
Description | designation |
---|---|
— The limit of proportionality (the yield strength for the residual strain) [MPa] | sT |
— Short-term strength [MPa] | sre |
— Reduction [%] | y |
— Elongation at break [%] | d5 |
— Brinell hardness in [MPa] | HB |
— Impact strength [kJ / m2] | KCU |
Weldability:
designation | Description |
---|---|
limited weldability | — Needs to preheating t ° 100−120 ° C with a final heat treatment |
no limits | — No need for preliminary heating and final heat treatment |
difficult to weld | — Needs to preheating t ° 200−300 ° C with a final heat treatment |
Basic properties
Titanium welding wire produced in degassed and etching condition. Its roundness must not exceed tolerances. Its surface must be clean and bright, with no shades of tint, neprotravov or dark spots. Traces broaches, small risks, sunsets deeper than shown in the table.
The diameter of the wire VT20−2 St. | The wire brand VT20−2 St. depth of the defect must be no more than |
---|---|
1.0 | - |
1.2 | - |
1.4 | - |
1.6 | - |
1.8 | - |
2.0 | 0.4 |
2.5 | 0.5 |
3.0 | 0.5 |
3.5 | 0.6 |
4.0 | 0.6 |
5.0 | 0.7 |
6.0 | 0.8 |
7.0 | 0.8 |
Note. On a surface of acceptable small diameter wire defects ≤ 3 mm — less than 0.1 mm. When Ø> 3 mm — 0.2 mm. The number of defects exceeding Macrosection depth should be within 10%. Correct defects or surface contaminants by etching the etching is allowed to re-wire coils degassing.
Supply
Presented wire brand VT20−2 St certified. The technical documentation included data on its chemical composition, limiting the percentage of impurities; mechanical properties. We can buy in bulk, any semi-finished products for large-scale productions. We also offer optimal conditions for retail customers. High level of service and efficiency of service are the face of our company.
Wire comes bays with outer diameter up to 900 mm. This wire must not be stuck together turns or bends of more than 100 °. Curl the wire after annealing, is not considered marriage. Coil weight — 50 kg. If the bay is made up of individual parts, the length of each of them must be more than 10 m.
Bay tightly ligated soft titanium wire in 3 places and wrapped in plain paper, and then synthetic cloth or plastic film, thickness 0,1−0,2 mm — 10 according to GOST 354−82 without paper packaging. On top of this bay ligated string of regulatory documents, respectively.
The mechanical characteristics of wire must conform to the requirements specified in the table.
Material | GOST | σ in | ψ | δ 5 |
---|---|---|---|---|
Wire VT20−2 St. | 27 265−87 | 635−835 | 35 |
σ in — Tensile strength [MPa]
δ 5, — Elongation at break [%]
ip — Reduction [%]
Marking
The label indicates the bay:
— Brand wire;
— The manufacturer and its trademark:
— № smelting and parties;
— date of manufacture;
— Designation of GOST.
— The availability of those. control;
Buy at a bargain price
All titanium alloys, implemented by LLC «Electrovek-steel» correspond to GOST and international quality standards. We supply titanium mill products in standard and custom sizes in the shortest possible time from the stores located in the territory of Russia and Ukraine. High quality, reasonable prices and a wide selection of products define the face of our company. As our regular customer, you can count on a discount system of discounts. Cooperation with us will help you to implement any engineering plans. We are waiting for your orders at evek.org site.