Bronze Bro8c4 (БрОЦ8-4)

  • Bronze БрО3Ц8С4Н1 (БрОЦСН3-8-4-1)
  • Bronze БрО8Ц4 (БрОЦ8-4)
  • Bronze БрО8С21 (БрОС8-21)
  • Bronze БрО8С12 (БрОС8-12)
  • Bronze БрО8Н4Ц2 (БрОНЦ8,5-4-2)
  • Bronze БрО6Ц6С3 (БрОЦС6-6-3)
  • Bronze БрО6Ц6С2х (БрОЦС6-6-2х)
  • Bronze БрО6Ц4С2Н1 (БрОЦСН6-4-2-1)
  • Bronze БрО6С6Ц3
  • Bronze БрО6К2Ц1
  • Bronze БрО5Ц6С5 (БрОЦС5-6-5)
  • Bronze БрО5Ц5С5 (БрОЦС5-5-5)
  • Bronze БрО5С25 (БрОС5-25)
  • Bronze БрО4Ц8С5
  • Bronze БрО4Ц7С5 (БрОЦС3,5-7-5)
  • Bronze БрО4Ц4С17 (БрОЦС4-4-17)
  • Bronze БрО3Ц7С5Н1 (БрОЦСН3-7-5-1)
  • Bronze БрО3Ц6С5 (БрОЦС3-6-5)
  • Bronze БрО3Ц13С4 (БрОЦС3-13-4)
  • Bronze БрО3Ц12С5 (БрОЦС3-12-5)
  • Bronze БрО3,5Ц7С5
  • Bronze BrO19
  • Bronze БрО16С5 (БрОС16-5)
  • Bronze БрО10Ц2Н2 (БрОЦН10-2-2)
  • Bronze БрО10Ц2Н1,5 (БрОЦН10-2-1,5)
  • Bronze БрО10Ц2 (БрОЦ10-2)
  • Bronze БрО10Ф1 (БрОФ10-1)
  • Bronze БрО10Ф0,7Н0,5 (БрОФН10-0,7-0,5)
  • Bronze БрО10С2Н3 (БрОСН10-2-3)
  • Bronze БрО10С10 (БрОС10-10)

    • Designation

    Name The value
    Designation GOST Cyrillic БрО8Ц4
    Designation GOST Latin BpO8Ts4
    Transliteration BrO8Ts4
    By chemical elements BaSn8Zn4
    Name The value
    Designation GOST Cyrillic БрОЦ8-4
    Designation GOST Latin BpOTs8-4
    Transliteration BrOTs8-4
    By chemical elements BaSnZn8-4

    Description

    Bronze Bro8c4 used: for the manufacture of castings parts fittings, shaped parts of pipelines; pumps operating in sea water; casting parts for shipbuilding, ship engineering and instrumentation.

    Standards

    Name Code Standards
    Non-ferrous metals, including rare, and their alloys В51 GOST 613-79
    Castings, non-ferrous metals and alloys В84 OST 5Р.9209-82

    Chemical composition

    Standard S P Si Ni Fe Cu As Al Zn Sn Sb Pb Mg
    GOST 613-79 ≤0.05 ≤0.05 ≤0.02 ≤2 ≤0.3 Rest ≤0.15 ≤0.02 4-6 7-9 ≤0.3 ≤0.5 ≤0.02
    Cu is the basis.
    According to GOST 613-79 and OST 5P.9209-82, the total content of impurities should be ≤ 1.00%. Impurities not regulated by the standard are included in the total amount of impurities. The sum of impurities of silicon and aluminum should not exceed 0.020%. In bronze, not intended for casting parts operating under hydraulic pressure, the manufacturer's agreement with the consumer allows the mass fraction of aluminum to 0.050% and silicon - up to 0.050%. The mass fraction of nickel due to copper and the amount of impurities is not included. The mass fraction of lead, as agreed by the manufacturer with the consumer, is allowed up to 1.50%, in which case the total amount of impurities is not included. In bronze intended for welded structures, the mass fraction of lead should be no more than 0.050%.

    Mechanical properties

    sT|s0,2, MPa σU, MPa d5, % KCU, kJ/m2 HB, MPa
    Castings are supplied without heat treatment. The permanent mold in the ground, centrifugal, investment casting, shell moulded
    ≥78.4 ≥196 ≥10 ≥196 ≥75

    Description mechanical marks

    Name Description
    sT|s0,2 Yield strength or limit of proportionality with a tolerance for residual deformation of 0.2%
    σU Limit short-term strength
    d5 Elongation after rupture
    KCU Toughness
    HB Brinell hardness number