Brass LC16K4 (ЛК80-3L)

  • Brass LSdh
  • Brass ЛЦ40Сd (ЛС59-1ЛД)
  • Brass LC40S (LS59-1L)
  • Brass ЛЦ40Мц3Ж (ЛМцЖ55-3-1)
  • Brass ЛЦ40Мц3А
  • Brass ЛЦ40Мц1,5 (ЛМц58-2L)
  • Brass LC40AJ
  • Brass ЛЦ38Мц2С2
  • Brass ЛЦ37Мц2С2К
  • Brass LC30A3 (LA67-2,5)
  • Brass ЛЦ25С2
  • Brass LC23A6Zh3Mz2
  • Brass ЛЦ16К4 (ЛК80-3L)
  • Brass ЛЦ14К3С3
  • Brass LC10 (L90L)
  • Brass LSch
  • LSd brass
  • LS Brass
  • Brass VOC
  • Brass LMZSCA
  • Brass LMZSC
  • Brass LMZS (LMZS58-2-2)
  • Brass LMZKA
  • Brass LMZh
  • LKS Brass
  • Brass LK2
  • Brass LK1
  • Brass LC
  • Brass LAMZ (LAMZ66-6-3-2)
  • Brass LA

    • Designation

    Name The value
    Designation GOST Cyrillic ЛЦ16К4
    Designation GOST Latin LTs16K4
    Transliteration LTs16K4
    By chemical elements ЛZn16Co4
    Name The value
    Designation GOST Cyrillic ЛК80-3Л
    Designation GOST Latin LK80-3L
    Transliteration LK80-3L
    By chemical elements ЛCo80-3

    Description

    Brass LC16K4 used: for the manufacture of castings of complex configuration parts, fixtures and fittings operating at temperatures to +250 °C and exposed to hydrovodone testing; casting parts for shipbuilding, marine engineering and instrumentation, working in the sea water while providing cathodic protection (gear, parts of friction units); casting parts of valves and actuators to it.

    Note

    Brass siliceous.

    Standards

    Name Code Standards
    Non-ferrous metals, including rare, and their alloys В51 GOST 17711-93, GOST Р 50425-92, OST 4.021.009-92, OST 4.021.011-92
    Castings, non-ferrous metals and alloys В84 OST 1 90046-72, OST 5Р.9209-82
    Cast iron castings (grey and malleable cast iron) В81 OST 24.207.01-90

    Chemical composition

    Standard P Mn Si Ni Fe Cu Al Zn Sn Sb Pb
    OST 5Р.9209-82 ≤0.1 ≤0.8 3-4.5 ≤0.2 ≤0.6 78-81 ≤0.04 Rest ≤0.3 ≤0.1 ≤0.5
    Zn is the basis.
    According to GOST 17711-93 and OST 5P.9209-82, the total amount of impurities should be ≤ 2.5%. Impurities not specified are taken into account in the total amount of impurities. The mass fraction of nickel in brass is allowed at the expense of copper and is not included in the sum of impurities. Upon agreement of the manufacturer with the consumer, the mass fraction of aluminum is allowed up to 0.10% in the manufacture of parts that do not require hydraulic density.

    Mechanical properties

    sT|s0,2, MPa σU, MPa d5, % KCU, kJ/m2 HB, MPa
    Castings are supplied without heat treatment
    ≥117.6 ≥343 ≥15 ≥686 ≥110
    ≥117.6 ≥294 ≥15 ≥686 ≥100
    ≥117.6 ≥294 ≥12 ≥392 -
    Casting investment casting according to OST 1 90046-72 (samples separately cast or cut from castings)
    - ≥245 ≥10 - ≥90

    Description mechanical marks

    Name Description
    sT|s0,2 Yield strength or limit of proportionality with a tolerance for residual deformation of 0.2%
    σU Limit short-term strength
    d5 Elongation after rupture
    KCU Toughness
    HB Brinell hardness number

    Physical characteristics

    Temperature Е, HPa r, kg/m3 l, W/(m · °C) R, Mr. · m
    20 104 8200 879 200

    A description of the physical symbols

    Name Description
    r Density
    l Coefficient of thermal conductivity
    R UD. the resistivity