Aluminium AD1 (1013)

  • Aluminum 1050
  • Aluminum 1145
  • Aluminum AD (1015)
  • Aluminum AD0 (1011)
  • Aluminum AD00 (1010)
  • Aluminum AD000
  • Aluminum AD1 (1013)
  • ADS Aluminum

    • Designation

    Name The value
    Designation GOST Cyrillic АД1
    Designation GOST Latin AD1
    Transliteration AD1
    By chemical elements -
    Name The value
    Designation GOST Cyrillic 1013
    Designation GOST Latin 1013
    Transliteration 1013
    By chemical elements 1013

    Description

    Aluminium AD1 is used: for the manufacture of flat ingots, cast by semi-continuous method or continuous casting, and is intended for rolling into sheets, strips and other semi-finished products (strips, plates, profiles, panels, rods, tubes, drawn wire, stampings and forgings) by hot or cold deformation, as well as ingots and slabs; sheets used in the printing industry; profiles pressed extra virgin for the manufacture of radiators of cooling of semiconductor devices; foil used to manufacture capacitors; pressed large pipes; special profiles by cold extrusion; cold-formed profiles for the cladding of building structures; extruded pipes with controlled inner diameter from 14 to 42 mm for heat exchangers; heat exchangers evaporators and condensers with two-sided bulge of the channel used in domestic refrigerators and freezers; roll foil used for thermal, hydro and sound insulation; cold-rolled foil intended for packaging of food, drugs, medical devices, cosmetic products industry, as well as for the production of packaging materials based on it; bimetallic sheets with the steel grade 08CR18NI10TI; tape in rolls clad with copper on one side (APM-1) and intended for various products in the electrical industry; round wire for cold upsetting.

    Note

    ISO 209−1 aluminum brand AD1 is designated А199,3.

    Standards

    Name Code Standards
    Tape В54 GOST 1018-77, GOST 13726-97, TU 1-2-404-80, TU 1-2-421-81, TU 1-2-432-82, TU 1-2-433-82, TU 1-2-434-82
    Wire from nonferrous metals and their alloys В74 GOST 14838-78, OST 1 92005-2002, OST 4.021.101-92
    Tubes of non-ferrous metals and alloys В64 GOST 18475-82, GOST 18482-79, OST 1 92048-90, OST 1 92048-76, OST 4.021.119-92, OST 1 92047-76, TU 1-1-198-89, TU 1-3-118-91, TU 1-3-120-92, TU 1-3-138-91, TU 1-3-67-90, TU 1-3-26-93, TU 1-3-019-93, TU 1-3-67-98
    Bars В55 GOST 21488-97, OST 4.021.017-92
    Non-ferrous metals, including rare, and their alloys В51 GOST 4784-97, GOST 9498-79, GOST 19437-81, OST 1 92014-90, OST 4.021.009-92
    Sheets and strips В53 GOST 618-73, GOST 10703-73, GOST 17232-99, GOST 21631-76, GOST 25001-81, GOST 25905-83, GOST 745-2003, OST 4-021.048-78, OST 4.021.092-92, TU 1-9-1048-87, TU 1-9-413-84, TU 1-9-4-85, TU 1-9-637-74, TU 1-9-688-82, TU 1-9-548-87
    Bars and shapes В52 GOST 8617-81, GOST 13616-97, GOST 13617-97, GOST 13618-97, GOST 13619-97, GOST 13620-90, GOST 13621-90, GOST 13622-91, GOST 13623-90, GOST 13624-90, GOST 13737-90, GOST 13738-91, GOST 17575-90, GOST 17576-97, GOST 18591-91, GOST 24767-81, GOST 29296-92, GOST 29303-92, GOST Р 50066-92, GOST Р 50067-92, GOST Р 50077-92, OST 1 92093-83, OST 1 92069-77, TU 1-9-631-73
    Processing of metals by pressure. Forgings В03 OST 26-01-152-82

    Chemical composition

    Standard Mn Si Fe Cu Al Ti Zn Mg
    GOST 4784-97 ≤0.025 ≤0.3 ≤0.3 ≤0.05 ≥99.3 ≤0.15 ≤0.1 ≤0.05
    Al is the base.
    According to GOST 4784-97, the mass fraction of other impurities is ≤ 0.05% of each, the total mass fraction of all impurities is ≤ 0.70%. For aluminum AD1pl, the mass percentages of impurities are set: silicon ≤ 0.30%, copper ≤ 0.020%, manganese ≤ 0.025%, magnesium ≤ 0.050%, iron ≤ 0.30%, zinc ≤ 0.10%, titanium ≤ 0.150, (not regulated) impurities of each ≤ 0.010%.

    Mechanical properties

    Section, mm sT|s0,2, MPa σU, MPa d5, % d d10
    The tape is supplied according to GOST 1018-77 (samples)
    0.3-0.7 - ≥70 - ≥20 -
    0.3 - 100-150 - ≥2.5 -
    0.35-0.7 - 120-150 - ≥3 -
    Full hard sheet for the printing industry (0,35-0,80 mm) as supplied
    - 135-195 - - ≥4
    Sheet metal in delivery condition according to GOST 21631-76, OST 4.021.047-92 tape according to GOST 13726-97 (samples transverse)
    5-10.5 - ≥70 - ≥15 -
    0.3-0.5 - ≥60 - ≥20 -
    0.5-0.9 - ≥60 - ≥25 -
    0.9-10.5 - ≥60 - ≥30 -
    0.3-0.8 - ≥145 - ≥3 -
    0.8-3.5 - ≥145 - ≥4 -
    3.5-10.5 - ≥130 - ≥5 -
    0.8-4.5 - ≥100 - ≥6 -
    Plates according to GOST 17232-99. 4.021.061-92 supplied without heat treatment (samples transverse)
    11-25 - ≥78 ≥18 - -
    25-80 - ≥64 ≥15 - -
    Forging after annealing at OST 26-01-152-82
    ≥30 ≥60 ≥25 - -
    The wire drawn according to OST 1 92005-2002
    3.9-12 - - - ≥20 -
    Extruded normal strength according to GOST 8617-81 on delivery
    - ≥59 ≥20 - -
    The special extruded profile with subsequent drawing GOST 18591-91 (as supplied)
    - ≥98 - - -
    Round bars normal strength in the delivery condition in the OST 4.021.017-92 (longitudinal samples)
    8-250 - ≥60 ≥25 - -
    The pressed bars normal strength in the delivery condition according to GOST 21488-97 (longitudinal samples)
    8-300 - ≥60 ≥25 - -
    Extruded aluminum tubes with internal diameter control for heat exchangers as supplied without a heat treatment on the other 1-3-67-90 (in the section you specify an internal pipe diameter)
    14-42 - 59-98 - ≥28 -
    Tubes extruded in the state of delivery according to GOST 18482-79 (samples, in cross-section shows the thickness of the wall)
    - ≥60 ≥20 - -
    Large-size extruded tubes according to OST 1 92048-76 on delivery
    - ≥59 ≥20 - -
    Cold-rolled tubes in the delivery condition according to GOST 18475-82, OST 4.021.119-92 samples (in cross-section shows the thickness of the wall)
    - 60-110 - - ≥20
    ≤2 - ≥110 - - ≥4
    2-5 - ≥100 - - ≥5
    Foil as supplied by OST 4.021.092-92 (samples)
    0.007-0.011 - ≥30 - - -
    0.011-0.045 - ≥35 - ≥2 -
    0.045-0.2 - ≥40 - ≥3 -
    0.007-0.045 - ≥100 - - -
    0.045-0.2 - ≥120 - - -

    Description mechanical marks

    Name Description
    sT|s0,2 Yield strength or limit of proportionality with a tolerance for residual deformation of 0.2%
    σU Limit short-term strength
    d5 Elongation after rupture
    d Elongation after rupture
    d10 Elongation after rupture

    Physical characteristics

    Temperature Е, HPa r, kg/m3 l, W/(m · °C) R, Mr. · m a, 10-6 1/°C
    20 71 2710 - 292 -
    100 - - 226 - 24
    200 - - - - 256

    A description of the physical symbols

    Name Description
    Е The normal elasticity modulus
    r Density
    l Coefficient of thermal conductivity
    R UD. the resistivity
    С Specific heat